| ITEM | T200 |
| Basic function | Maximum frequency | 0～600.00Hz |
| Carrier frequency | 0.5kHz～16kHz |
| The carrier frequency can be automatically adjusted based on the load features. |
| Input frequency resolution | Digital setting:0.01Hz |
| Analog setting: maximum frequency×0.025% |
| Control mode | Voltage/Frequency control (V/F) |
| Sensorless flux vector control (No PG) |
| Closed loop vector control (Have PG) |
| Startup torque | G Type:0.5Hz/150%(No PG)； |
| P Type:0.5Hz/100% |
| Speed range | 1:100(No PG) |
| Speed stability accuracy | ±0.5%(No PG) |
| Torque control accuracy | ±5%(Have PG) |
| Overload capacity | G type: 60s for 150% of the rated current, 3s for 180% of the rated current. |
| P type: 60s for 120% of the rated current, 3s for 150% of the rated current |
| Torque boost | Fixed boost |
| Customized boost 0.1%–30.0% |
| V/F curve | Straight-line V/F curve |
| Multi-point V/F curve |
| N-power V/F curve (1.2-power, 1.4-power, 1.6-power,1.8-power, square) |
| V/F separation | Two types: complete separation; half separation |
| Ramp mode | Straight-line ramp |
| S-curve ramp |
| Four groups of acceleration/deceleration time with the range of 0.0–6500.0s |
| DC braking | DC braking frequency: 0.00 Hz to maximum frequency |
| Braking time: 0.0-100.0s |
| Braking action current value: 0.0%–100.0% |
| JOG control | Jog frequency range:0.00Hz~50.00Hz. JOG acceleration/deceleration time0.0s~6500.0s. |
| Onboard Multiple preset speeds | It implements up to 16 speeds via the simple PLC function or by input terminal states |
| Onboard PID | It realizes process-controlled closed loop control system easily. |
| Auto voltage | It can keep constant output voltage automatically when the mains voltage changes. |
| regulation (AVR) |
| Over-voltage/ | The current and voltage are limited automatically during the running process so as to avoid frequent tripping due to over-voltage/over-current. |
| Over-current stall |
| control |
| Rapid current limit | It helps to avoid frequent over-current faults of the inverter. |
| Torque limit and torque control | It can limit the torque automatically and prevent frequent over-current tripping during the running process. |
| Individualized function | High performance | Control of asynchronous motor is implemented through the high-performance current vector control technology. |
| Instantaneous stop doesn’t stop | The load feedback energy compensates the voltage reduction so that the AC drive can continue to run for a short time. |
| Timing control | Timing range 0.0Min～6500.0Min |
| Communication methods | RS-485 |
| Operation | Running command channel | Given by the panel, control terminals, |
| Serial communication port, can be switched by many ways |
| Frequency source | 10 kinds of frequency source, given by digital analog voltage, analog current, Pulse, serial port. can be switched by many ways |
| Auxiliary frequency source | There are ten auxiliary frequency sources. It can implement fine tuning of auxiliary frequency and frequency synthesis |
| Input terminals | 5 digital input terminals, one of which supports up to 100 kHz high-speed pulse input; |
| 1 analog input terminal, supports 0-10V voltage input or 4–20 mA current input. |
| Output terminal | 1 digital output terminal |
| 1 relay output terminal |
| 1 analog output terminal :that supports 0–20 mA current output or 0–10 V voltage output |
| Display and operation panel | LED display | It displays the parameters. |
| Key locking and | It can lock the keys partially or completely and define the |
| function selection | function range of some keys so as to prevent mis-function. |
| Protection mode | Motor short-circuit detection at power-on, input output phase loss protection, over-current protection, over-voltage protection, under voltage protection, overheat protection and overload protection. |
| Environment | Installation location | Indoor, avoid direct sunlight, dust, corrosive gas, combustible gas, oil fog, steam, drip or salt. |
| Altitude | Lower than 1000 m(Lower the grades when using higher then 1000m) |
| Ambient temperature | -10°C ～40°C (Lower the grades if the ambient temperature is between 40°C and 50°C) |
| Humidity | Less than 95%RH, without condensing |
| Vibration | Less than 5.9m/s2(0.6g) |
| Storage temperature | －20℃~＋60℃ |
